Introduction

If you are a laser engraving enthusiast, you usually like doing some crafts in your spare time, such as photo engraving, wooden block toys, personalized metal markings, etc. This cheap Tyvok Spider A1 800L foldable laser engraver should be more suitable for you. The Tyvok Spider A1 800L folding design makes it suitable for placement in the corner of your home, making it very simple to unfold the engraver for use when it is needed. Importantly, it is relatively affordable, making it ideal for laser engraving enthusiasts.

The Tyvok Spider A1800L has a laser module with only 10W of power and a maximum engraving area of 800*400mm. Of course, it supports the purchase of other extensions, such as an air-assisted air pump, a touch screen, a line drawing module, and more. So, if you are just a laser engraving enthusiast and don’t want to pay too much, the Tyvok Spider A1800L Folding Laser Engraver will be one of the options available to you.

Unboxing

The Tyvok Spider A1 800L that I received is the basic kit, and what you see in the picture below is all there is. A folded-up A1800L engraver, a 10W diode 450nm laser module, foldable honeycomb work boards, a goggle, a USB cable, a power supply, and the necessary screwdriver and laser focus adjustment tool.

What's in the box

Tyvok Spider A1800L’s Design: foldable style and larger working area

The Tyvok Spider A1 800L laser engraver has a folding design style, so it is very good for storage. This foldable design is the first time I’ve seen it in the LaserPecker LX1 series, but it’s too expensive, so the Tyvok Spider A1800L would be a cheaper alternative. When the Spider A1800L is needed, just unfold the frame, this is to get an engravable area of 800*400mm.

Tyvok Spider laser engraver’s honeycomb work panels have also been innovated to match the folding style, and are no longer a single non-detachable piece like other honeycomb panels. Therefore the Spider A1800L matching honeycomb board is also foldable, I can put together the honeycomb base plate according to the size of the engraving area. When the engraving is complete, it can be folded up and placed in a corner just like the laser engraver, greatly reducing the amount of space it takes up.

Tyvok Spider A1800L

Because the Tyvok Spider A1800L is foldable and the modules are interchangeable, installation of the laser module is very easy and efficient, with almost zero assembly work required for the overall product.

However, perhaps due to cost control, the Tyvok Spider A1800L still uses manual laser focus adjustment. Due to its low price, this is understandable, and manual focus adjustment is easy to do. It’s just that I think it would be nice to have an autofocus feature so that I don’t start a new project and damage the material or have to go back to the first step to refocus because I forgot to manually adjust the laser focus.

laser focus manually

Tyvok Spider A1 800L performance review: what I enjoyed about it

1. Engraving and cutting wooden crafts

As a laser engraver enthusiast, the most common application is engraving and cutting wood, and the A1800L’s 10W of laser power is more than enough for engraving wood, as well as cutting common thicknesses of plywood, such as the 3-5mm plywood used to make wooden building blocks and toys.

For my project, I used the Spider A1800L to engrave a welcome sign for my studio in 4mm black walnut which is 61mm * 165mm. I used the LightBurn software with the laser power set at 50% and the engraving speed at 6000 mm/min. The total time for the engraving was 23 minutes.

Tyvok Spider A1800L engraving walnut

As you can see in the picture below, with 50% laser power and 6000mm/min engraving speed, the text is very clear on the walnut. So, for wood crafting, Spider A1 800L is basically satisfied. Of course, I must admit that it is a bit slow to engrave, as you need to wait for about 23 minutes to finish engraving an area of 61*165mm, however, you can concentrate on other things during the waiting process.

Walnut craft made by Tyvok Spider A1800L laser engraver

2. Black acrylic photo engraving and cutting

Another common application for laser engraving hobbyists would be to engrave photos with wonderful memories. Therefore, I also used the Tyvok Spider A1 800L to create a black acrylic photo. For this project, I needed to set up the parameters for engraving the photo and the cutting parameters for cutting 2mm black acrylic.

In the black acrylic photo project, I need to set the image mode to Grayscale, to better reproduce the details of the image on the black material. The image engraving speed is 6000mm/min, the maximum laser power is 30%, 200DPI. The cutting parameters for cutting 2mm black acrylic are 100% laser power and 120 cutting speed.

Black acrylic picture engraving and cutting parameters
engraving and cutting black acrylic

The waiting time for a complete engraving of a 107*56mm size acrylic photo is 18 minutes, which is acceptable to me. Looking closely at the black acrylic photo compared to the original photo, it lost some details. Maybe I didn’t find a more correct engraving parameter setting, but it doesn’t matter, at least it proves that the Spider A1800L can realize a better engraving and cutting ability of acrylic, even though it only has 10W laser power.

acrylic photo made by Tyvok Spider A1800L

3. Excellent details reproduce engraving on black paper

Engraving my favorite photos and framing them as decoration is the most important need for me to use the engraving machine. However, using black acrylic to make photos in the previous, I may not be able to find a very accurate engraving parameter setting, failing to highly reproduce the details of the photos. Here, I found an easier way to use the Tyvok Spider A1 800L laser engraver to make art photos, that is to use black paper instead of black acrylic.

For the project of creating black paper photos, you still need to set the image mode to Grayscale, the engraving speed to 6000mm/min, the maximum engraving power to 15%, and set 200 DPI. Then cut the paper according to the size of the photo area, the cutting parameters can be 100% laser power, and 1200mm/min engraving speed.

balck paper photo engraving

The finished product is shown below, with the details of the original photo nicely reproduced by laser engraving! However, getting this artwork only took me 15 minutes. The Spider A1800L’s image engraving ability was finally put to good use, and the image details it engraved on the black paper were perfectly well reproduced, even the details of the character’s hair strings and the hat’s threads were engraved, so I was very satisfied with it!

balck paper photo engraving

Using the same engraving parameters, I again engraved Monica’s stage photo on black paper and placed it on a transparent frame for decoration. Without a doubt, the photo was still engraved perfectly. It is worth mentioning here that if you also want to engrave pictures on black material, it is better to convert the color pictures into grayscale format beforehand. This way the laser engraver will be able to give better engraving results.

black paper Photo engraving
black paper photo engraved by Spider A1800L

4. Meet your metals engraving need

Although the Tyvok Spider A1 800L only has a 10W diode blue laser module, it still has good metal marking capabilities. To test its metal engraving capability, I first used the Spider A1800L to engrave an aluminum sheet with the engraving parameters of 100% laser power, 200mm/min engraving speed, and 300 lines per inch. For sure, it has a good engraving effect on the aluminum sheet, but the speed is a bit slow because the logo engraving took about 15 minutes.

Tyvok Spider A1800L engraving aluminum sheet

I tried to engrave only one pass on stainless steel using the engraving parameters of 100% laser power, 400mm/min engraving speed, and 300 lines per inch. It took about 25 minutes to complete the engraving of a 25*54mm area. To be sure, the Tyvok Spider A1800L still engraved a very clear pattern on the stainless steel, however, due to the 10W laser power limitation, I was not able to get a colorful engraving effect on the stainless steel.

But as a laser engraving with only 10W power and at such a cheap price. With such entry-level metal engraving capabilities, it can satisfy the needs of those who are interested in engraving.

Tyvok Spider A1800L engraving stainless steel

5. Compatibility of other materials

The Tyvok Spider A1 800L is a 450nm blue laser engraver, so like any other high power 450nm blue laser engraver, it can engrave a very wide range of materials, in addition to the ones tried above, leather can be engraved perfectly and doesn’t require much laser power. In addition, the Spider A1800L can also engrave stones, plastics, bamboo, etc., which are not shown in the article.

leather engraving

6. Low noise and dumping protection

If you are using a laser engraver in your home, noise is one of the factors that you need to consider. Since the Tyvok Spider A1800L has only 10W of laser power, it does not require the assistance of a powerful cooling fan. Therefore, the noise is very low when I use it, as seen by the decibel meter test result, the surrounding noise is only 59 decibels when the Spider A1800L is working, so using it at home will not disturb others due to the noise.

low noise

In addition, the Tyvok Spider A1800L has tilt protection. In case the laser engraving is tilted, the machine will detect it and stop the laser output within 2 seconds.

dumping protection

Pros and Cons

Pros

  • Cheaper
  • Foldable
  • Lightweight
  • Module interchangeable
  • No need to assemble
  • Flexible honeycomb working plate
  • Good image details reproduction on black materials
  • 800* 400mm maximum engraving area
  • Good material compatibility
  • Low working noise

Cons

  • Open frame
  • Manual laser focus
  • Low engraving speed
  • 10W laser Power
  • Manual engraving positioning

Final thought

The first and biggest benefit of the Tyvok Spider A1 800L is its affordability, which certainly gives a lot of laser engraving hobbyists confidence in their purchase. It comes in a foldable design style, which maximizes the user’s need for storage space as well as eliminating the need for assembly.

During my actual use of it, I think it meets the engraving needs of laser engraving hobbyists, but of course, I have to admit that the Tyvok Spider A1 800L is an entry-level laser engraver, and the 10W laser power and lack of an enclosed structure, like Spider X1C, make it unsuitable for handling complex engraving or cutting projects.

But I don’t think that’s a bad thing, the affordability of the Tyvok Spider A1800L dictates its cost-control requirements, so other features must be cut. All in all, if you’re an amateur with a passion for laser engraving and don’t want to invest too much money in a professional laser engraving machine, the Tyvok Spider A1800L foldable laser engraver would be a dependable alternative for you.

Tyvok Spider laser engraver